NOTE ON PERFORMANCE TESTING

Transcription

1 NOTE ON PERFORMANCE TESTING Performance Profile Sheet(s) are included in a format that can be easily photocop ied for each trainee. Performance tests are designed to mea sure competency in the s taught in each module. Please note the number of s to be tested while teaching each module. Each trainee should be tested on all the s listed on the Performance Profile Sheet(s). Before performance, the instructor should brief the trainees on: Test objectives and criteria Safety precautions Procedures for each to be tested The instructor administering the performance should also do the following: Ensure that all of the needed equip ment is available and operating properly. Set up the stations. Organize and administer the test in a way that allows for optimal per for mance. Complete the Performance Profile Sheet(s) for each trainee by assigning a pass/fail score for each listed. Also, include the date for each in the rating box. Monitor adherence to all safety regulations and precautions. Provide adequate supervision to prevent injuries. Take immediate and effective action to remedy any emergency. Performance Testing If Performance Testing is done as part of the National Center for Construction Education and Research Standardized Craft Training Program, the following conditions must be met: 1. The Craft Instructor must hold valid NCCER instructor cer ti fi ca tion for the craft being tested. 2. The training must be delivered through a Accredited Training Sponsor recognized by NCCER. 3. For every module, the specific performance must be completed to the satisfaction of the instructor. 4. The results of the must be recorded on the Training Report Form 200. This form must be provided to the local Accredited Training Sponsor to be forwarded to the NCCER National Registry. Certified Plus Credential Provided the sponsor is working through an NCCER-Accredited Assessment Center, candidates who successfully pass performance may be eligible for a Certified Plus Credential. A number of NCCER s Performance Profiles cross over to NCCER s Assessment Performance Verifications and may be completed simultaneously. Go to and select the Assessments tab to locate the Performance Verifications associated with this craft. Note two other important conditions are required for the Certified Plus Credential: 1. Candidates must first pass the associated written assessment. 2. An NCCER-Accredited Assessment Administrator must sign off on the Performance Verification before it is submitted to NCCER.

2

3 Module has no Performance Profile Sheet; no performance is required for this module.

4 Craft: Industrial Maintenance E & I Technician Module Number: Module Title: Process Mathematics Contren Learning Series Rating Levels: (1) Passed: performed (2) Failed: did not perform Rating Levels: (1) Also, Passed: list the performed date the for (2) each Failed: did was not completed. perform Recognition: Also, When list the date for the NCCER for Standardized each was Craft completed. Training Program, Recognition: When be sure to record for the Per NCCER for mance Standardized results Craft on Training Craft Training Program, Report be Form sure 200, to record and submit Performance the results to the results Training on Program Craft Training Sponsor. Report Certified Plus Form 200, and submit the results to the Training Program Sponsor. Credential: Trainees who successfully complete these performance s may be 2 1. Find the point where Fahrenheit equals Celsius Do three temperature conversions, using figures provided by your instructor Calculate differential pressure using values provided by your instructor Calculate the volume of a vessel using variables provided by your instructor. Copyright 2008 National Center for Construction Education and Research. Permission is granted to reproduce this page PROCESS MATHEMATICS MODULE PERFORMANCE PROFILE 7.5

5 Module has no Performance Profile Sheet; no performance is required for this module.

6 Craft: Industrial Maintenance E & I Technician Module Number: Module Title: Instrument Drawings and Documents, Part One Contren Learning Series Rating Levels: (1) Passed: performed (2) Failed: did not perform Also, list the date the for each was completed. Recognition: When for the NCCER Standardized Craft Training Program, be sure to record Performance results on Craft Training Report Form 200, and submit the results to the Training Program Sponsor. Certified Plus Credential: Trainees who successfully complete these performance s may be Locate and identify drawing elements as specified by your instructor. Copyright 2008 National Center for Construction Education and Research. Permission is granted to reproduce this page INSTRUMENT DRAWINGS AND DOCUMENTS, PART ONE MODULE PERFORMANCE PROFILE 11.5

7 Craft: Instrumentation Module Number: Module Title: Electrical Systems for Instrumentation STANDARDIZED CRAFT TRAINING SERIES Rating Levels: 1. (1) Passed: performed. (2) Failed: did not perform Also, list the date the for each was completed. 2. Failed: did not perform. Recognition: When for the NCCER Standardized Craft Training Program, Recognition: When be sure to record for the Per NCCER for mance Standardized results Craft on Training Craft Training Program, Report be Form sure 200, to record and submit Performance the results Profile to the Training results Program on Craft Sponsor. Training Report Form 200 and submit the results to the Training Program Sponsor. Certified Plus Credential: Trainees who successfully complete these performance s may be 3 1. Under the supervision of the instructor, measure and record the current, voltage, and resistance in a DC circuit Using any two of the measured values, calculate the power consumed by the circuit. Copyright 2001 National Center for Construction Education and Research. Permission is granted to reproduce this page INSTRUMENTATION LEVEL ONE MODULE PERFORMANCE PROFILE 4.5

8 Craft: Instrumentation Module Number: Module Title: Relays and Timers Rating Rating Levels: Levels: 1. (1) Passed: Passed: performed performed. (2) Failed: did not perform Also, list the date the for each was completed. Recognition: 2. When Failed: did for not the perform NCCER. Standardized Craft Training Program, Recognition: When be sure to record for the Per NCCER for mance Standardized results Training on Craft Program, Training be Report sure to record Form 200, Performance and submit the results to on the NCCER Training Training Program Report Sponsor. Form 200 Certified Plus and submit the results to the Training Program Sponsor. Credential: Trainees who successfully complete these performance s may be 2, 4, 5, 6 1. Select and install various types of relays Select and install various types of timers. Copyright 2003 National Center for Construction Education and Research. Permission is granted to reproduce this page INSTRUMENTATION LEVEL TWO MODULE PERFORMANCE PROFILE 8.5

9 Craft: Instrumentation Module Number: Module Title: Switches and Photoelectric Devices Rating Levels: 1. (1) Passed: performed. (2) Failed: did not perform 2. Also, Failed: list the did date not the perform. for each was completed. Recognition: When for the NCCER Standardized Craft Training Program, Recognition: When for the NCCER Standardized Training Program, be sure to be sure to record Per for mance results on Craft Training Report record Performance results on NCCER Training Report Form 200 Form 200, and submit the results to the Training Program Sponsor. and submit the results to the Training Program Sponsor. Certified Plus Credential: Trainees who successfully complete these performance s may be 1, 2, 3, 4 1. Select and install various switches. 6, 7 2. Select and install various photoelectric devices. Copyright 2003 National Center for Construction Education and Research. Permission is granted to reproduce this page INSTRUMENTATION LEVEL TWO MODULE PERFORMANCE PROFILE 9.5

10 (PAGE 1 OF 2) Craft: Industrial Maintenance E & I Technician Module Number: Module Title: Tubing Contren Learning Series Rating Levels: (1) Passed: performed (2) Failed: did not perform Also, list the date the for each was completed. Recognition: Certified Plus Credential: When for the NCCER Standardized Craft Training Program, be sure to record Per for mance results on Craft Training Report Form 200, and submit the results to the Training Program Sponsor. Trainees who successfully complete these performance s may be 5 1. Bend copper tubing at 45-degree and 90-degree angles using a compression-type bender Cut and deburr copper tubing using a hacksaw or tubing cutter Cut and deburr stainless steel tubing. continued Copyright 2008 National Center for Construction Education and Research. Permission is granted to reproduce this page TUBING MODULE PERFORMANCE PROFILE 9.5

11 (PAGE 2 OF 2) Craft: Industrial Maintenance E & I Technician Module Number: Module Title: Tubing Contren Learning Series 7 4. Install a flare fitting on a section of copper tubing Properly make up an instrument tubing connection with a compression fitting, then loosen and re-tighten it. Copyright 2008 National Center for Construction Education and Research. Permission is granted to reproduce this page 9.6 INDUSTRIAL MAINTENANCE E & I MECHANIC LEVEL TWO MODULE PERFORMANCE PROFILE

12 Craft: Industrial Maintenance E & I Technician Module Number: Module Title: Layout and Installation of Tubing and Piping Systems Contren Learning Series Rating Levels: (1) Passed: performed (2) Failed: did not perform Also, list the date the for each was completed. Rating Levels: 1. Passed: performed. Recognition: When for the NCCER Standardized Craft Training Program, be 2. sure Failed: to record did not Per perform mance. results on Craft Training Report Form 200, and submit the results to the Training Program Sponsor. Recognition: When for the NCCER Standardized Craft Training Program, Certified Plus Credential: Trainees be sure to who record successfully Performance complete Profile these performance results on s Craft may Training be eligible Report for Form a Certified 200 and Plus submit Credential. the results Refer to the to the Training Note on Program Performance Spons 1 1. Given a partial system equipment location diagram (one loop) and observing all considerations covered in this module, create an isometric drawing of the given loop. 2, 3 2. Measure and bend the tubing sections in the loop and select the fittings needed to install the layout shown in the isometric drawing in Performance Task # Indicate the types and locations of minimal support needed for the tubing installation Make up compression fittings on tubing. Copyright 2009 National Center for Construction Education and Research. Permission is granted to reproduce this page INDUSTRIAL MAINTENANCE E & I TECHNICIAN MODULE PERFORMANCE PROFILE 9.7

13 Craft: Industrial Maintenance E & I Technician Module Number: Module Title: Clean, Purge, and Test Tubing and Piping Systems Contren Learning Series Rating Rating Levels: Levels: (1) (1) Passed: Passed: performed performed (2) (2) Failed: Failed: did did not not perform perform Also, Also, list list the the date date the the for for each each was was completed. completed. Recognition: When for the NCCER Standardized Craft Training Program, Recognition: When be sure to record for the Per NCCER for mance Standardized results Craft on Training Craft Training Program, Report be Form sure 200, to record and submit Performance the results to the results Training on Program Craft Training Sponsor. Report Form 200, and submit the results to the Training Program Sponsor. Certified Plus Credential: Trainees who successfully complete these performance s may be 6 1. Set up and perform a pressure leak test Inspect the system to verify there is no leakage Perform a blowdown/purge Document the test results and restore the system to be serviceready. Copyright 2008 National Center for Construction Education and Research. Permission is granted to reproduce this page CLEAN, PURGE, AND TEST TUBING AND PIPING SYSTEMS MODULE PERFORMANCE PROFILE 10.5

14 Craft: Industrial Maintenance E & I Technician Module Number: Module Title: Electronic Components Contren Learning Series Rating Rating Levels: Levels: (1) (1) Passed: Passed: performed performed (2) (2) Failed: Failed: did did not not perform perform Also, Also, list list the the date date the the for for each each was was completed. completed. Recognition: When for the NCCER Standardized Craft Training Program, Recognition: When be sure to record for the Per NCCER for mance Standardized results Craft on Training Craft Training Program, Report be Form sure 200, to record and submit Performance the results to the results Training on Program Craft Training Sponsor. Report Form 200, and submit the results to the Training Program Sponsor. Certified Plus Credential: Trainees who successfully complete these performance s may be 6 1. Using a cross reference manual, identify a substitute for a selected electronic component Build a simple bridge rectifier circuit and view the results Check diodes. Copyright 2009 National Center for Construction Education and Research. Permission is granted to reproduce this page ELECTRONIC COMPONENTS MODULE PERFORMANCE PROFILE 2.3

15 Craft: Instrumentation Module Number: Module Title: Panel-Mounted Instruments Rating Levels: 1. (1) Passed: performed. (2) Failed: did not perform Also, list the date the for each was completed. 2. Failed: did not perform. Recognition: When for the NCCER Standardized Craft Training Program, Recognition: When be sure to record for the Per NCCER for mance Standardized results Training on Craft Program, Training be Report sure to record Form 200, Performance and submit the results to on the NCCER Training Training Program Report Sponsor. Form 200 and submit the results to the Training Program Sponsor. Certified Plus Credential: Trainees who successfully complete these performance s may be 2 1. Lay out an instrument panel Install an instrument in a panel. Copyright 2003 National Center for Construction Education and Research. Permission is granted to reproduce this page INSTRUMENTATION LEVEL TWO MODULE PERFORMANCE PROFILE 12.3

16 (PAGE 1 OF 2) Craft: Instrumentation Module Number: Module Title: Installing Field-Mounted Instruments Rating Levels: (1) Passed: performed (2) Failed: did not perform Also, list the date the for each was completed. Recognition: Certified Plus Credential: When for the NCCER Standardized Craft Training Program, be sure to record Per for mance results on Craft Training Report Form 200, and submit the results to the Training Program Sponsor. Trainees who successfully complete these performance s may be 2 1. Fabricate a floor-mounted instrument stand Install an orifice plate between two flanges Assemble and install a thermowell assembly on a section of 4-inch process piping. continued Copyright 2003 National Center for Construction Education and Research. Permission is granted to reproduce this page INSTRUMENTATION LEVEL TWO MODULE PERFORMANCE PROFILE 13.7

17 (PAGE 2 OF 2) Craft: Instrumentation Module Number: Module Title: Installing Field-Mounted Instruments 4 4. Identify selected pipe flange facings Identify selected pipe flange gaskets Install a three-valve manifold on a differential pressure transmitter using futbols. Copyright 2003 National Center for Construction Education and Research. Permission is granted to reproduce this page 13.8 INSTRUMENTATION LEVEL TWO MODULE PERFORMANCE PROFILE

18 Craft: Instrumentation Module Number: Module Title: Grounding and Shielding of Instrumentation Wiring Rating Levels: Rating Levels: (1) Passed: performed (2) Failed: did not perform Also, 1. Passed: list the date performed the. for each was completed. Recognition: When 2. Failed: did for not the perform NCCER. Standardized Craft Training Program, be sure to record Per for mance results on Craft Training Report Recognition: When for the NCCER Standardized Training Program, be sure to Form 200, and submit the results to the Training Program Sponsor. record Performance results on NCCER Training Report Form 200 Certified Plus and submit the results to the Training Program Sponsor. Credential: Trainees who successfully complete these performance s may be 1,2 1. Identify and explain the function of an equipment ground in a given drawing Draw an example of a ground loop Identify and explain the function of an equipment shield in a given drawing. Copyright 2003 National Center for Construction Education and Research. Permission is granted to reproduce this page INSTRUMENTATION THREE MODULE PERFORMANCE PROFILE 6.3

19 Module has no Performance Profile Sheet; no performance is required for this module.