INTRODUCTION Lighting petrol station forecourts can be extremely costly especially when operating a 24 hour premises when the filling area must be lit throughout the night but customer visits may be infrequent in the early hours of the morning. The Kanopy must be lit effectively so as not to deter potential customers however the energy costs incurred by doing so can be extremely high, the Dexeco Kanopy luminaire provides a simple solution to this problem. The Kanopy is available with two lumen outputs and beam angles ensuring it can be used to replace both HID and fluorescent luminaires. Dexeco can also offer a range of custom sized trims to suit the existing cut out in your canopy to ensure that no expensive modifications are required during installation. With two sensor options, the R11 sensor for presence detection and the R44 sensor for both presence detection and daylight regulation, the Kanopy can be programmed to dim back to lower output during periods of absence ensuring that the canopy remains lit whilst providing large energy savings throughout the night. Both sensor types can be programmed with our REA-AP controller from ground level ensuring that the settings can be easily modified allowing you to customise how long the luminaire remains at full output for and the level to which it dims back to along with a range of other customisable settings. The Kanopy provides rapid return on investment against both fluorescent and HID luminaires through a combination of low cost installation, highly efficient LED sources providing up to 125 luminaire lumens per circuit watt and sensor control ensuring that the luminaire is only operating when necessary but without compromising the appearance of the station during hours of darkness. T: 01747 858100 E: sales@dexeco.co.uk Page 1 of 8
APPLICATION Exterior Parking/Exterior Transport Warehouse/Storage SPECIFICATION Construction White powder painted steel housing. Internal injection moulded optical cover with 8,700 lumen version. Internal Miro 851 reflector to maximise optical efficiency. Clear polycarbonate diffuser. Performance Up to 125 luminaire lumens per circuit watt. 87% Light Output Ratio. Constant lumen output function eliminates depreciation of the source over lifetime. Philips Lumileds LM80 verified: 90% LED lumen maintenance for 60,000 operating hours. Philips Lumileds LM80 verified: B10 10% of LED s will exceed 10% lumen depreciation at 60,000 operating hours. Standard Deviation Colour Match 3 Step Macadam s Ellipse. L2 compliant. ECA compliant. Control Available with R11H (presence detection) and R44SA (presence detection and daylight regulation) sensors. Programmable from ground level with the Dexeco REA-AP remote control. Installation Custom trim sizes allow for installation in a range of canopy apertures minimising modifications required to the canopy and therefore reducing the cost of installation. Range of lumen outputs and beam distributions allows for one for one installation at a range of heights and spaces ensuring the wiring and canopies do not need to be modified. Variations Two beam angles, lumen outputs and sensor options available to allow you to customise the Kanopy to suit your canopy height and luminaire layout. T: 01747 858100 E: sales@dexeco.co.uk Page 2 of 8
IMAGES Product Images Project Images T: 01747 858100 E: sales@dexeco.co.uk Page 3 of 8
TECHNICAL Frame Sold Separately Kanopy 650 x 300mm T: 01747 858100 E: sales@dexeco.co.uk Page 4 of 8
Kanopy 650 x 650mm Kanopy 700 x 400mm Kanopy 700 x 700mm WARRANTY All Dextra products are supplied with a 12 month warranty for any defect that may occur with the product during this time. Any defect will either be repaired on site free of charge or the defective product may be replaced on a chargeable basis and credit given against defective product returned. The course of action taken will be at our discretion and dependent on the nature of the defect. The control gear within our high frequency and LED luminaires is further underwritten by our suppliers for a period of up T: 01747 858100 E: sales@dexeco.co.uk Page 5 of 8
to 5 years in total from the time of purchase. This comprises labour and parts for the first 3 years and free of charge components only for the final 2 years. PROTEC LED FR 8W GU10 luminaires and all Emergency LED ranges such as LED 3, EXI, HBE, OAT, OEZ, AME, OEH and TWS * are exempt from the 5 year warranty and are supplied with 1 year warranty only. PROTEC LED COB luminaires are supplied with a two year warranty for replacement luminaires only. All warranties are subject to correct use of the product and will be invalidated by misuse, for example incorrect installation or unsuitable environmental conditions. It is the duty of the customer to ensure that all relevant tests have been carried out prior to requesting site visits or replacement products, for example replacement of lamps, commissioning of sensors and inspection of external wiring. In the event that no defect is found with the product our costs for attending site will be recharged to the customer and credit will not be issued against returned products. No consequential losses incurred resulting from any defect with our product will be reimbursed. Consumable commodities such as lamps, starters and batteries are excluded from these warranty terms. Batteries are supplied with a twelve month warranty only. 5 year warranty on LED product ranges is subject to a maximum of 4000 operating hours per year and only applies where failures exceed the component manufacturers expected failure rate and lumen depreciation. If you require any assistance with regards to our products please do not hesitate to contact our Customer Services department on 01747 858100. *The LED4 Emergency LED range is supplied with a three year battery warranty and 5 year luminaire warranty. ORDER CODES Luminaire Codes Code Description Circuit Wattage Llm/w PFC L87 C84 Petrol Forecourt Kanopy, 7038llm, Colour 84 (ECA) 58.2w 120 PFC L87 OP C84 Petrol Forecourt Kanopy, 6646llm, Opal Diffuser, Colour 84 (ECA) 58.2w 114 PFC L110 C84 Petrol Forecourt Kanopy, 8712llm, Colour 84 (ECA) 76.4w 114 PFC L110 OP C84 Petrol Forecourt Kanopy, 8404llm, Opal Diffuser, Colour 84 (ECA) 76.4w 110 PFC FRAME 650x300 Kanopy Frame, 650mm x 300mm PFC FRAME 650x650 Kanopy Frame, 650mm x 650mm PFC FRAME 700x400 Kanopy Frame, 700mm x 400mm PFC FRAME 700x700 Kanopy Frame, 700mm x 700mm All Kanopy luminaires require a separate frame for installation, please order PFC FRAME with each luminaire and specify dimensions. Lighting Control Code Description R11HW Reacta 11, HFR, Wide Lens R44SH Reacta 44, Shallow, DSI
Kanopy LED Luminaire 230-240V / 50-60Hz IP40 IK00 1 WARNING - THIS LUMINAIRE MUST BE EARTHED This luminaire has been tested and is manufactured to comply with BS EN 60598 : specification for general requirements and tests. It should be installed by a suitably qualified person in accordance with IEE. CAUTION: there is a potential risk of electric shock from the LED boards when the product is operational with the cover removed. NOTE: INSTALLATION AND OPERATION OF THE LUMINAIRE BEYOND ITS SCOPE OF SUPPLY WILL INVALIDATE THE WARRANTY. 2 Using suitable screws, secure the frame into the ceiling aperture through the holes most suited. There is a selection of depths available for use when installing. Gently insert frame into aperture in ceiling. The frame should match the dimensions of the ceiling cut out. 3 4 Using a gentle twisting motion, insert the main body into the frame. The two screwson the body should mate with the two slots in the sides of the frame. NOTE: Ensure the mains cable does not become trapped when inserting the main body. Insert the remaining screws through the selected holes into the ceiling struts. 5 6 As shown, slide the main body along the slots in the frame until it reaches the end. These slots should act as pivots for the body. DIL-0125-0001_C Make a secure mains connection between the body and the cable in the ceiling. Ensure all excess cabling is stored above the luminaire safely so not to be trapped when closed. 26/01/16
Kanopy LED Luminaire 7 8 Once connected, close the luminaire by pushing the main body up into the frame. A pin latch inside the luminaire will secure the body in the closed position. Ensure the pin latch has been closed properly before moving on. To release the body from the frame, a small push on the pin latch end will release it, and allow it to pivot down. 9 10 11 12 13 14 DIL-0125-0001_C 26/01/16