ASBESTOS ABATEMENT WORK PLAN APARTMENT BUILDINGS AT 80 BIRCH STREET AND 92 WALNUT STREET LEWISTON, MAINE BID #

ASBESTOS ABATEMENT WORK PLAN APARTMENT BUILDINGS AT 80 BIRCH STREET AND 92 WALNUT STREET LEWISTON, MAINE BID # 2013-049 Prepared for: City of Lewiston 27 Pine Street Lewiston, Maine 04240 Prepared by: SUMMIT ENVIRONMENTAL CONSULTANTS 640 Main Street Lewiston, Maine 04240 August 19, 2013 Project No. 13-3170.3

ASBESTOS ABATEMENT WORK PLAN 80 BIRCH STREET AND 92 WALNUT STREET LEWISTON, MAINE On behalf of the City of Lewiston (the City), Summit Environmental Consultants, Inc. (Summit) has prepared this Asbestos Abatement Work Plan (Work Plan) for the removal of Asbestos- Containing Materials (ACM) from apartment buildings located at 80 Birch Street and 92 Walnut Street in Lewiston, Maine. 1.0 PROJECT OBJECTIVE AND SCOPE OF WORK The project objective is: 80 Birch Street The removal and proper disposal of ACM roofing, siding material, and wall plaster. 92 Walnut Street The removal and proper disposal of ACM sheet flooring and ceiling plaster. The scope and sequence of work to be completed under this contract is presented in this Work Plan (refer to Section 2.0; Sequence of Work). The apartment buildings are not occupied and are scheduled for demolition following completion of abatement/remediation activities. Work shall be performed in accordance with applicable Maine Department of Environmental Protection (MEDEP), U.S. Environmental Protection Agency (USEPA), U.S. Department of Transportation (DOT) and the Occupational Safety and Health Administration (OSHA) regulations. Location and estimated quantities of ACM are included in Table 1 and shown on Figures 1 through 7. Laboratory analytical results for suspect ACM sampled are presented in Appendix A. The Contractor is responsible to determine actual quantities of identified ACM for quote preparation and abatement purposes. 80 Birch Street and 92 Walnut Street Page WP-2 Asbestos Abatement Work Plan

TABLE 1 ASBESTOS-CONTAINING BUILDING MATERIALS Location Asbestos-containing Material (ACM) Type Estimated Quantity of ACM Comments 80 Birch Street Throughout Wall Plaster 800 square feet (SF) Entryway, stairs, and second floor bedroom Roof Roofing material 308 SF Second floor rear roof Garage Asphalt siding 40 SF Interior front wall 92 Walnut Street 2nd Floor ACM Sheeting flooring 10 SF Kitchen cabinets ACM multi-layer sheet flooring 50 SF Bathroom ACM ceiling plaster 50 SF Bathroom 2.0 SEQUENCE OF WORK 2.1 GENERAL A. The Contractor shall prepare a sequence of work and asbestos abatement project design for respective work areas. The sequence of work will be subject to review and approval by City. An Asbestos Abatement Project Design Consultant licensed by the MEDEP, and representing the Abatement Contractor, shall prepare all asbestos abatement project designs. Designs will be subject to review from Summit and the MEDEP. B. Summit will pre-notify MEDEP to facilitate a start date of September 12, 2013. The Contractor will be responsible to properly revising and re-notifying the MEDEP and the USEPA of the asbestos abatement and subsequent demolition (by others). Notifications fees will have been submitted to the MEDEP by Summit. C. The buildings are scheduled for demolition following completion of asbestos abatement work. D. The Contractor will be responsible for work area security for the duration of the abatement work. E. The Contractor shall be responsible for providing electricity, water, and sanitary facilities for his/her use during the course of the abatement work. F. Hazardous and Universal Waste removal is not included in this contract. 80 Birch Street and 92 Walnut Street Page WP-3 Asbestos Abatement Work Plan

2.2 TYPICAL SEQUENCE OF WORK A typical sequence of work will include, but may not be limited to, the following steps: A. Prepare asbestos abatement work areas in accordance with the Contractor's asbestos abatement design (prepared by a MEDEP licensed Asbestos Abatement Design Consultant) and with current State of Maine Asbestos Management Regulations, Chapter 425. B. Perform asbestos abatement work in compliance with all applicable State and Federal laws and regulations. ACM shall be adequately wet during the removal process utilizing amended water. The Contractor shall select abatement methods appropriate for the existing conditions. C. Package ACM waste for disposal by double bagging in 6 mil poly bags or double wrapping in 6-mil poly sheeting. Prior to bagging or wrapping, waste that may puncture disposal bags or wrap shall be enclosed with burlap or other suitable material that will prevent bag failure. D. Transport and properly dispose/recycle removed wastes, residuals, debris, materials and equipment. E. Demobilize from the site including removal of barriers, disposable items and equipment. 3.0 HEALTH AND SAFETY 3.1 GENERAL A. All asbestos abatement work shall be performed in full compliance with applicable State and Federal laws and regulations. Personnel present within the boundaries of the regulated area shall wear respiratory protection and shall be dressed in full body disposable clothing. B. Abatement personnel shall be appropriately trained for the assigned work task in accordance with applicable MEDEP and Federal regulations. 4.0 SCHEDULE A. A Site walk-through will be conducted on August 27, 2013 at 10:00 at 80 Birch Street, followed by a subsequent walk-through at 92 Walnut Street. Attendance at this Site walk is mandatory. B. Quotes are due to the City by September 4, 2013 at 2:00 pm. C. The Pre-Construction Meeting and project start date is September 12, 2013. 80 Birch Street and 92 Walnut Street Page WP-4 Asbestos Abatement Work Plan

D. Unless otherwise approved by the City, work associated with this contract (with exception of disposal manifests) shall be completed by October 11, 2013. 5.0 PROJECT MEETINGS A. Project progress meetings will be conducted as deemed necessary by the City and/or the Contractor. 6.0 CLEARANCE/ACCEPTANCE CRITERIA A. Work will be evaluated for completion following the removal of visible residue from the interior and exterior of the buildings. This evaluation will be completed by the Contractor's supervisor, subsequent to completion of successful asbestos abatement clearance inspection, sampling and analysis for the work area. Visual evaluation protocol will include: 1. Entering the work area where the abatement/clean-up/remediation activity was performed. 2. Inspection of the surfaces from which ACM and associated residue was removed. 3. Examination of the permanent features within the work area such as walls, windows, etc., and attempting to determine whether residual materials or visible debris is present. 4. Examination of the decontamination and waste-load out facilities and observe whether residual material or visible debris is present. The waste will be evaluated to determine proper containerization and labeling. B. The Contractor is responsible for providing final asbestos abatement clearance inspection, sampling and analysis for the work area. Clearances will be performed in accordance with MEDEP regulations by an independent, MEDEP licensed Asbestos Project Monitor hired by the Contractor. 7.0 PROJECT DOCUMENTATION A. The Contractor will provide the following documentation to the City representative: Finalized MEDEP Form N (Project Notification) Asbestos Abatement Project Design(s) (signed by a MEDEP licensed Asbestos Abatement Design Consultant) Crew Daily Sign-in Logs Chronological Project Log Asbestos Consultant Independent Business Relationship Disclosure Form Final Inspection and Clearance Documentation Air Sample Analysis Results 80 Birch Street and 92 Walnut Street Page WP-5 Asbestos Abatement Work Plan

Asbestos Disposal & Documentation Form 8.0 CONTRACT ADMINISTRATION 8.1 Measurement and Payment A. This project will be quoted by the Contractor on a lump sum basis. The lump sum quote will include furnishing necessary labor, materials, equipment, disposal costs and permitting, etc. to complete the work. B. The Contractor shall submit one lump sum application for payment for the work associated with this project, minus retainage. Payment shall include full compensation for all required labor, products, tools, equipment, plant, transportation, services and incidentals; erection, application or installation of an item of the Work; overhead and profit. C. The City will withhold retainage of 10% from the pay requisition until final completion (i.e., receipt of final waste manifests). D. The Contractor shall promptly pay each subcontractor, upon receipt of payment from the City, out of the amount paid to the Contractor on account of such subcontractor's work, the amount to which said subcontractor is entitled. The Contractor shall, by appropriate agreement with each subcontractor, require each subcontractor to make payments to its subcontractors in a similar manner E. Prior to release of retainage, the Contractor shall file, with the City, an executed Waiver and Release of Claims stating that bills for all items of labor, material and parts have been paid and no claims exist against the City. F. A final inspection of the work area will be made by the City and the Contractor to determine whether the specified work has been completed. 8.2 Provisions for Extra Work A. All extra work under this Contract shall only be performed under written change orders to the original contract and issued by the City. B. The Contractor shall not start any extra work until the prices for the extra work involved and the amount of extension of contract time, if any, resulting from the extra work have been agreed upon, or compensation has been established, in writing, by the City and the Contractor. C. The City shall have the right, by verbal instructions, to make minor changes in the Scope of Work not involving additional cost and not inconsistent with the purpose of the original Scope of Work. 80 Birch Street and 92 Walnut Street Page WP-6 Asbestos Abatement Work Plan

D. All extra work involving cost or changes in the scope of the Work shall be previously agreed to and as ordered in writing by the City. No claim for a change to the Contract Price shall be valid unless so ordered. 9.0 QUOTING REQUIREMENTS 9.1 Site Investigation A. By submitting a quote, the Contractor acknowledges that he/she has investigated and satisfied themself as to: a) the conditions affecting the work, including but not limited to physical conditions of the site which may bear upon site access, handling and storage of tools and materials, access to water, electric or other utilities or otherwise affect performance or required activities. b) the character and quantity of all surface and subsurface materials or obstacles to be encountered in so far as this information is reasonably ascertainable from an inspection of the site, including exploratory work done by the City or a designated consultant, as well as information presented in drawings and specifications included with his contract. Any failure by the Contractor to acquaint himself with available information will not relieve him from responsibility for estimating properly the difficultly or cost of successfully performing the work. The City is not responsible for any conclusions or interpretations made by the Contractor on the basis of the information made available by the City. 9.2 Discrepancies and Explanations A. Should a contractor find discrepancies in the plans and/or specifications or should he/she be in doubt as to the meaning or intent of any part thereof, he/she must, no later than August 30, 2013, request clarification from the City. Discrepancies with regard to conflicts between the Contract Documents and applicable Federal, State, or Local regulations or requirements shall be included herein. Failure to require such clarification is a waiver to any claim by the Contractor for expense made necessary by reason of later interpretation of the Contract Documents by the City. B. Explanations desired by a prospective Contractor regarding this Work Plan, drawings or other documents shall be requested in writing (e.g., email) no later than September 3, 2013. Requests shall include the project name and shall be directed to: Norm Beauparlant, Director and Budget/Purchasing City of Lewiston 27 Pine Street Lewiston, Maine 04240 Fax: (207) 784-2959 Email: nbeauparlant@lewistonmaine.gov 80 Birch Street and 92 Walnut Street Page WP-7 Asbestos Abatement Work Plan

C. Oral explanations or instructions will not be binding. Only written addenda are binding. Any addenda resulting from these requests will be mailed to all listed holders of the Quote Documents no later than one day prior to the quote opening. The Contractor shall acknowledge the receipt of all addenda on the quote proposal form. 9.3 Modification and Withdrawal of Quotes A. Withdrawal or modifications to quotes are effective if written notice thereof is filed prior to time and at the place of quote opening. A notice of withdrawal or modifications to a Quote must be signed by the Contractor or his designated representative. B. No withdrawal or modifications shall be accepted after the time for opening of proposals. 9.4 Quote Security A. A 10% Quote Security shall be submitted with the Quote in the form of a Bid Bond or a certified check. 9.5 Insurance requirements A. The Contractor shall purchase and maintain insurance that will protect him/her from claims that may arise out of the result from his activities under this contract, whether those activities are performed by the Contractor or by any Subcontractor or by anyone directly or indirectly employed by any of them or anyone for whose acts any of them may be liable. B. The insurance required shall be written for not less than the following, or greater if required by law. 1. Workmen s Compensation: State Statutory Coverage 2. Comprehensive General Liability (including Premises Operations; Independent Contractor s protective; Products and Completed Operations; Broad Form Property Damage; Asbestos Abatement; Pollution): Bodily Insurance Property Damage $1,000,000 each Occurrence $2,000,000 Aggregate $1,000,000 each Occurrence $2,000,000 Aggregate 3. Contractual Liability (Hold Harmless Coverage): 80 Birch Street and 92 Walnut Street Page WP-8 Asbestos Abatement Work Plan

Bodily Injury Property Damage $1,000,000 each Occurrence $1,000,000 each Occurrence $2,000,000 Aggregate 4. Comprehensive Automobile Liability (owned, non-owned, and hired): Bodily Insurance Property Damage $500,000 each Occurrence $1,000,000 Aggregate $500,000 each Occurrence C. Certificate of Insurance acceptable to the City shall be furnished to the City prior to commencement of the work. D. If the City permits the Contractor to use any of the City s equipment, tools, or facilities, such use will be gratuitous and the Contractor shall release the City from any responsibility arising from claims for personal injuries, including death, arising out of the use of such equipment, tools, or facilities irrespective of the condition thereof or any negligence on the part of the City in permitting their use. E. The Certificate of Insurance shall name the City of Lewiston and Summit Environmental Consultants as additional insured. F. Performance and Payment Bonds will not be required for this project. 9.6 Licenses and Qualifications A. Contractors must be licensed as required by Construction Firm Law of Maine. B. Contractors must be licensed as required by the State of Maine, Department of Environmental Protection, Solid Waste Bureau, for purpose of removal, encapsulation, enclosure, demolition and maintenance of structures or components as stated in 06-096 Department of Environmental Protection Chapter 425, Asbestos Management regulations. 9.7 Rejection of Quotes A. The City reserves the right to reject quotes for any reason that serves the best interests of the City or this Project. The City also reserves the right to waive any technicality or irregularity in a quote. Failure to submit requested information/documentation may result in automatic disqualification of quote package. 80 Birch Street and 92 Walnut Street Page WP-9 Asbestos Abatement Work Plan

9.8 Quoting A. All perspective contractors shall visit the project site prior to preparing quotes. Quantities provided in this Work Plan are for informational purposes only. Actual determination of project quantities for removal and recycling/disposal shall be the responsibility of the Contractor. B. One copy of the quote is due to the City by 2:00 P.M. on September 4, 2013. Quotes will be addressed to the attention of: Norm Beauparlant, Director of Budget/Purchasing City of Lewiston 27 Pine Street Lewiston, Maine 04240 D. Fax copies of the quote will not be accepted. E. Bidders shall submit the following documentation upon the request of the Director of Purchasing: Proposed Project Schedule Current MEDEP Asbestos Abatement Contractor License, Asbestos Abatement Designer License and Asbestos Abatement Supervisor license for the proposed project superintendent. 10.0 PRECONSTRUCTION PERIOD 10.1 CONTRACT A. The bidder recommended for award will be noticed by September 5, 2013. A formal Notice of Award will be September 9, 2013 following acceptance by the City of Lewiston Finance Committee. B. The successful contractor will contract directly with the City. 10.2 PRECONSTRUCTION SUBMITTALS A. Submittals including Abatement Contractor training and medical certifications, Certificate of Insurance, disposal facility, testing laboratory, etc., will be submitted for review by the City s representative at the Pre-Construction Meeting. B. Copies of the asbestos abatement designs, notifications and associated documentation will be submitted to the City s representative at the time of the Pre-Construction Meeting. 80 Birch Street and 92 Walnut Street Page WP-10 Asbestos Abatement Work Plan

Proposal Bid Sheet

PROPOSAL FORM CITY OF LEWISTON, MAINE ACM ABATEMENT AT 80 BIRCH STREET & 92 WALNUT STREET BID #: 2013-049 BID DATE: September 4, 2013 @ 2:00 PM PRE-BID: August 27, 2013 @10:00 AM TO: Norman Beauparlant, Director of Budget/Purchasing City of Lewiston City Hall, 27 Pine Street Lewiston ME 04240 Dear Sir: Have carefully examined the premises and existing conditions affecting the work, we, the undersigned, hereby agree to furnish all labor, materials, appliances, supplies, plants, equipment and other facilities incidental to the ACM Abatement as required by, and in strict accordance with, the Specifications dated August 19, 2013 as prepared by the City of Lewiston and that the undersigned will accept in full payment thereof of the following sum to wit: ITEM DESCRIPTION OF WORK Amount 1 ACM Abatement at 80 Birch Street as specified. $ 2 ACM Abatement at 92 Walnut Street as specified. $ TOTAL ITEM 1 & 2 $ The undersigned further agrees to complete work by: The undersigned acknowledges the receipt of addenda #: The undersigned further agrees that after notification by the City of the acceptance of his/her proposal and the readiness of the contract for signature, he/she will execute the contract within five (5) days, Saturdays, Sundays and holidays excepted, and that he/she will commence the work within five (5) days after the execution of the contract unless otherwise specified in the Supplemental Specifications or directed by the City in writing, and that he/she will prosecute the work to its completion. Performance & Payment Bonds are not required. The undersigned further agrees that in the employment of labor, preference will be given, all other things being equal, to the citizens of Lewiston and of the State of Maine, in that order.

The undersigned hereby further declares that the only person or parties interested in this proposal as principals are named below; that the proposal is made without any connection with any other person or party making any proposal for the same work; and that no person acting for or employed by the City of Lewiston is directly or indirectly interested in this proposal or in any contract which may be made under it or in profits expected to arise therefrom, except as provided by the City Charter. The full names and addresses of all persons or parties interested in this proposal as principals are named below; (Give first and last names in full; and in case of a corporation, give names and addresses of President, Treasurer and Manager; and in case of a partnership, give names and addresses of members): Accompanying this proposal is a bid security deposit in the amount of: % $ which is to become the property of the City by forfeiture if the undersigned fails, after notification by the Director of Budget/Purchasing of the acceptance of his/her proposal, to execute a contract with the City within five (5) days agreed to herein; or, in case the undersigned withdraws his/her proposal within thirty (30) days after the opening of the proposals. Otherwise, the deposit will be returned to the undersigned in accordance with the provisions in the Notice to Contractors. FIRM NAME SIGNATURE PRINTED/TYPED NAME TITLE LEGAL ADDRESS PLACE OF BUSINESS FIRM S IRS ID # DATE TELEPHONE # FAX # E-MAIL ADDRESS

Figures

Appendices

Appendix A LABORATORY ANALYTICAL REPORT

EMSL Analytical, Inc. 200 Route 130 North Cinnaminson, NJ 08077 Phone/Fax: (800) 220-3675 / (856) 786-5974 http://www.emsl.com / cinnasblab@emsl.com EMSL Order ID: Customer ID: Customer PO: Project ID: 041319149 SECI78 Attn: Proj: Suzanne Yerina Summit Environmental Consultants, Inc. 640 Main Street Lewiston, ME 04240 13-3170.2 92 Walnut Street Phone: (207) 795-6009 Fax: (207) 795-6128 Collected: Received: 7/19/2013 : 7/24/2013 Summary Test Report for Asbestos Analysis of Bulk Material via EPA 600/R-93/116 Method via Polarized Light Microscopy 001A 3rd kitchen/12" tan mottled Lab Sample ID: 041319149-0001 7/23/2013 Tan 001B 3rd kitchen/12" tan mottled Lab Sample ID: 041319149-0002 7/23/2013 Tan 001C 3rd kitchen/12" tan mottled Lab Sample ID: 041319149-0003 7/24/2013 Tan 002A 3rd kitchen/mastic (12" tan) Lab Sample ID: 041319149-0004 7/23/2013 Black 002B 3rd kitchen/mastic (12" tan) Lab Sample ID: 041319149-0005 7/23/2013 Black 002C 3rd kitchen/mastic (12" tan) Lab Sample ID: 041319149-0006 7/24/2013 Black 003A 3rd kitchen/tan multi sheet flooring - sheet flooring Lab Sample ID: 041319149-0007 7/23/2013 Tan /Various Test Report:EPAMultiTests-7.26.0 Printed: 7/24/2013 09:02AM Page 1 of 10

EMSL Analytical, Inc. 200 Route 130 North Cinnaminson, NJ 08077 Phone/Fax: (800) 220-3675 / (856) 786-5974 http://www.emsl.com / cinnasblab@emsl.com EMSL Order ID: Customer ID: Customer PO: Project ID: 041319149 SECI78 Summary Test Report for Asbestos Analysis of Bulk Material via EPA 600/R-93/116 Method via Polarized Light Microscopy 024A Roof/felt Lab Sample ID: 041319149-0070 7/24/2013 Black 024B Roof/felt Lab Sample ID: 041319149-0071 7/24/2013 Black 024C Roof/felt Lab Sample ID: 041319149-0072 7/24/2013 Black 025A Roof/tar Lab Sample ID: 041319149-0073 7/24/2013 Black 025B Roof/tar Lab Sample ID: 041319149-0074 7/24/2013 Black 025C Roof/tar Lab Sample ID: 041319149-0075 7/24/2013 Black PLM: Cert# BA-0133(AP) Cert# BA-0134(FD) PLM EPA NOB: Cert# BA-0133(AP) Cert# BA-0134(FD) Analyst(s) Anne Paul PLM (13) (21) Chelsey Bilhear (22) Frank Dicrescenzo PLM (7) (5) Stephen Siegel, CIH, Laboratory Manager or other Approved Signatory Any questions please contact Steve Siegel. EMSL maintains liability limited to cost of analysis. This report relates only to the samples reported above and may not be reproduced, except in full, without written approval by EMSL. This test report must not be used to claim product endorsement by NVLAP or any agency of the U.S. Government. EMSL bears no responsibility for sample collection activities or analytical method limitations. The laboratory is not responsible for the accuracy of results when requested to physically separate and analyze layered samples. PLM alone is not consistently reliable in detecting asbestos in floor coverings and similar NOBs Samples analyzed by EMSL Analytical, Inc. Cinnaminson, NJ NVLAP Lab Code 101048-0, AIHA-LAP, LLC-IHLAP Lab 100194, NYS ELAP 10872, NJ DEP 03036 Initial report from: 07/24/201309:02:14 Test Report:EPAMultiTests-7.26.0 Printed: 7/24/2013 09:02AM Page 10 of 10

EMSL Analytical, Inc. 200 Route 130 North Cinnaminson, NJ 08077 Phone/Fax: (800) 220-3675 / (856) 786-5974 http://www.emsl.com / cinnasblab@emsl.com EMSL Order ID: Customer ID: Customer PO: Project ID: 041319148 SECI78 Attn: Proj: Suzanne Yerina Summit Environmental Consultants, Inc. 640 Main Street Lewiston, ME 04240 13-3170.1 80 Birch Street Phone: (207) 795-6009 Fax: (207) 795-6128 Collected: Received: 7/19/2013 : 8/02/2013 Summary Test Report for Asbestos Analysis of Bulk Material via EPA 600/R-93/116 Method via Polarized Light Microscopy 001A 3rd kit/cream squared sheet flooring Lab Sample ID: 041319148-0001 7/23/2013 White 001B 3rd kit/cream squared sheet flooring Lab Sample ID: 041319148-0002 7/23/2013 White 001C 3rd kit/cream squared sheet flooring Lab Sample ID: 041319148-0003 7/23/2013 White 002A 3rd perimeter/red tar roof shingles Lab Sample ID: 041319148-0004 7/23/2013 Red /Black 002B 3rd perimeter/red tar roof shingles Lab Sample ID: 041319148-0005 7/23/2013 Red /Black 002C 3rd perimeter/red tar roof shingles Lab Sample ID: 041319148-0006 7/23/2013 Red /Black 003A Rear 2nd fl/black multilayer roof Lab Sample ID: 041319148-0007 7/23/2013 Black 0.0% 97.6% 2.4% Chrysotile Test Report:EPAMultiTests-7.26.0 Printed: 8/02/2013 12:01PM Page 1 of 7

EMSL Analytical, Inc. 200 Route 130 North Cinnaminson, NJ 08077 Phone/Fax: (800) 220-3675 / (856) 786-5974 http://www.emsl.com / cinnasblab@emsl.com EMSL Order ID: Customer ID: Customer PO: Project ID: 041319148 SECI78 Summary Test Report for Asbestos Analysis of Bulk Material via EPA 600/R-93/116 Method via Polarized Light Microscopy 008C 1st floor porch/multilayer roof Lab Sample ID: 041319148-0024 7/23/2013 Black /Green 7.3% 92.7% 009A sheetrock Lab Sample ID: 041319148-0025 PLM 7/23/2013 Brown/Tan/White 10% 90% <1% Chrysotile This is a composite result of wallboard, jt. compound, and tape. Tan joint compound present. 009B sheetrock Lab Sample ID: 041319148-0026 PLM 7/23/2013 Brown/White 12% 88% This is a composite result of wallboard, jt. compound, and tape. White joint compound present. 009C sheetrock Lab Sample ID: 041319148-0027 PLM 7/23/2013 Gray/Tan/White 20% 80% <1% Chrysotile This is a composite result of wallboard, jt. compound, and tape. 010A 1st kitchen/multicolor sheet flooring Lab Sample ID: 041319148-0028 7/23/2013 Brown /White 010B 1st kitchen/multicolor sheet flooring Lab Sample ID: 041319148-0029 7/23/2013 Brown /White 010C 1st kitchen/multicolor sheet flooring Lab Sample ID: 041319148-0030 7/23/2013 Brown /White 011A 1st living/green sheet flooring Lab Sample ID: 041319148-0031 7/23/2013 Brown /White Test Report:EPAMultiTests-7.26.0 Printed: 8/02/2013 12:01PM Page 4 of 7

EMSL Analytical, Inc. 200 Route 130 North Cinnaminson, NJ 08077 Phone/Fax: (800) 220-3675 / (856) 786-5974 http://www.emsl.com / cinnasblab@emsl.com EMSL Order ID: Customer ID: Customer PO: Project ID: 041319148 SECI78 Summary Test Report for Asbestos Analysis of Bulk Material via EPA 600/R-93/116 Method via Polarized Light Microscopy 016C 1st rear hall/cream sheet flooring Lab Sample ID: 041319148-0048 7/23/2013 Tan 017A Garage int wall/tar shingle Lab Sample ID: 041319148-0049 7/23/2013 Brown /Red /Black 0.0% 91.6% 8.4% Chrysotile 017B Garage int wall/tar shingle Lab Sample ID: 041319148-0050 7/23/2013 Positive Stop (Not ) 017C Garage int wall/tar shingle Lab Sample ID: 041319148-0051 7/23/2013 Positive Stop (Not ) PLM: Certification #BA-0146 (WN) & #BA-0148 (CB) Cert# BA-0147(PC) PLM EPA NOB: Certification #BA-0146 (WN) & #BA-0148 (CB) Analyst(s) Chelsey Bilhear PLM (2) (12) Patrick Carr PLM (2) William Nguyen PLM (5) (26) Stephen Siegel, CIH, Laboratory Manager or other Approved Signatory Any questions please contact Steve Siegel. EMSL maintains liability limited to cost of analysis. This report relates only to the samples reported above and may not be reproduced, except in full, without written approval by EMSL. This test report must not be used to claim product endorsement by NVLAP or any agency of the U.S. Government. EMSL bears no responsibility for sample collection activities or analytical method limitations. The laboratory is not responsible for the accuracy of results when requested to physically separate and analyze layered samples. PLM alone is not consistently reliable in detecting asbestos in floor coverings and similar NOBs Samples analyzed by EMSL Analytical, Inc. Cinnaminson, NJ NVLAP Lab Code 101048-0, AIHA-LAP, LLC-IHLAP Lab 100194, NYS ELAP 10872, NJ DEP 03036 Initial report from: 07/24/201306:46:33 Test Report:EPAMultiTests-7.26.0 Printed: 8/02/2013 12:01PM Page 7 of 7

EMSL Analytical, Inc. 200 Route 130 North, Cinnaminson, NJ 08077 Phone/Fax: (800) 220-3675 / (856) 786-5974 http://www.emsl.com cinnasblab@emsl.com EMSL Order: CustomerID: CustomerPO: ProjectID: 041321422 SECI78 Attn: Suzanne Yerina Summit Environmental Consultants, Inc. 640 Main Street Lewiston, ME 04240 Phone: (207) 795-6009 Fax: (207) 795-6128 Received: 08/09/13 9:20 AM Analysis Date: 8/13/2013 Collected: Project: 13-3170.1 80 BIRCH STREET Test Report: Asbestos Analysis of Bulk Materials via EPA 600/R-93/116 Method using Polarized Light Microscopy Asbestos Sample Description Appearance % Fibrous % Non-Fibrous % Type 014D 041321422-0001 015D 041321422-0002 014E 041321422-0003 2ND FLOOR BEDROOM #2 - PLASTER SKIM COAT 2ND FLOOR BEDROOM #2 - PLASTER BROWN COAT 2ND FLOOR LIVING ROOM - PLASTER SKIM COAT Gray/White Fibrous Homogeneous White Fibrous Homogeneous 5% Synthetic 95% Non-fibrous (other) left as composite, unable to seperate left as composite, unable to seperate 5% Synthetic 95% Non-fibrous (other) Insufficient Material 015E 041321422-0004 2ND FLOOR LIVING ROOM - PLASTER BROWN COAT Gray Fibrous Homogeneous 5% Synthetic 95% Non-fibrous (other) 014F 041321422-0005 2ND FLOOR BEDROOM #1 - PLASTER SKIM COAT Yellow Non-Fibrous Homogeneous 100% Non-fibrous (other) 015F 041321422-0006 2ND FLOOR BEDROOM #1 - PLASTER BROWN COAT Gray Fibrous Homogeneous 5% Synthetic 95% Non-fibrous (other) Analyst(s) Frank Dicrescenzo (5) Patrick Carr (3) Stephen Siegel, CIH, Laboratory Manager or other approved signatory EMSL maintains liability limited to cost of analysis. This report relates only to the samples reported and may not be reproduced, except in full, without written approval by EMSL. EMSL bears no responsibility for sample collection activities or analytical method limitations. Interpretation and use of test results are the responsibility of the client. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST or any agency of the federal government. Non-friable organically bound materials present a problem matrix and therefore EMSL recommends gravimetric reduction prior to analysis. Samples received in good condition unless otherwise noted. Estimated accuracy, precision and uncertainty data available upon request. Unless requested by the client, building materials manufactured with multiple layers (i.e. linoleum, wallboard, etc.) are reported as a single sample. Reporting limit is 1% Samples analyzed by EMSL Analytical, Inc. Cinnaminson, NJ NVLAP Lab Code 101048-0, AIHA-LAP, LLC-IHLAP Lab 100194, NYS ELAP 10872, NJ DEP 03036, PA ID# 68-00367 Initial report from 08/13/2013 12:13:19 Test Report PLM-7.28.9 Printed: 8/13/2013 12:13:37 PM 1

EMSL Analytical, Inc. 200 Route 130 North, Cinnaminson, NJ 08077 Phone/Fax: (800) 220-3675 / (856) 786-5974 http://www.emsl.com cinnasblab@emsl.com EMSL Order: CustomerID: CustomerPO: ProjectID: 041321422 SECI78 Attn: Suzanne Yerina Summit Environmental Consultants, Inc. 640 Main Street Lewiston, ME 04240 Phone: (207) 795-6009 Fax: (207) 795-6128 Received: 08/09/13 9:20 AM Analysis Date: 8/13/2013 Collected: Project: 13-3170.1 80 BIRCH STREET Test Report: Asbestos Analysis of Bulk Materials via EPA 600/R-93/116 Method using Polarized Light Microscopy Asbestos Sample Description Appearance % Fibrous % Non-Fibrous % Type 014G 041321422-0007 015G 041321422-0008 1ST FLOOR LIVING ROOM - PLASTER SKIM COAT 1ST FLOOR LIVING ROOM - PLASTER BROWN COAT Gray Fibrous Homogeneous Skim coat not present 5% Synthetic 95% Non-fibrous (other) Insufficient Material 014H 041321422-0009 1ST FLOOR BEDROOM #2 - PLASTER SKIM COAT White Non-Fibrous Homogeneous 100% Non-fibrous (other) Limited sample 015H 041321422-0010 1ST FLOOR BEDROOM #2 - PLASTER BROWN COAT Gray Fibrous Homogeneous 5% Synthetic 95% Non-fibrous (other) Cert# BA-0134(FD) Cert# BA-0147(PC) Analyst(s) Frank Dicrescenzo (5) Patrick Carr (3) Stephen Siegel, CIH, Laboratory Manager or other approved signatory EMSL maintains liability limited to cost of analysis. This report relates only to the samples reported and may not be reproduced, except in full, without written approval by EMSL. EMSL bears no responsibility for sample collection activities or analytical method limitations. Interpretation and use of test results are the responsibility of the client. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST or any agency of the federal government. Non-friable organically bound materials present a problem matrix and therefore EMSL recommends gravimetric reduction prior to analysis. Samples received in good condition unless otherwise noted. Estimated accuracy, precision and uncertainty data available upon request. Unless requested by the client, building materials manufactured with multiple layers (i.e. linoleum, wallboard, etc.) are reported as a single sample. Reporting limit is 1% Samples analyzed by EMSL Analytical, Inc. Cinnaminson, NJ NVLAP Lab Code 101048-0, AIHA-LAP, LLC-IHLAP Lab 100194, NYS ELAP 10872, NJ DEP 03036, PA ID# 68-00367 Initial report from 08/13/2013 12:13:19 Test Report PLM-7.28.9 Printed: 8/13/2013 12:13:37 PM THIS IS THE LAST PAGE OF THE REPORT. 2

Appendix B PROPOSED OWNER-CONTRACTOR AGREEMENT

AGREEMENT FOR SERVICES BETWEEN THE CITY OF LEWISTON AND CONTRACTOR Preamble THIS AGREEMENT (the "Agreement") is made this day of by and between The City of Lewiston (the City), with offices at 27 Pine Street, Lewiston, Maine 04240 and with offices at ("Contractor"), on the terms and conditions presented in this agreement and in the Contract Documents for the Asbestos Abatement Project, Apartment Buildings at 80 Birch Street and 92 Maple Street located in Lewiston, Maine, the City hereby engages the Contractor to provide the services set forth in the following Agreement and the Contractor agrees to perform the services for the compensation set forth in this Agreement and also agrees to be bound by the provisions of this Agreement. 1. Scope of Work This Agreement shall cover the Asbestos Abatement Project, Apartment Buildings at 80 Birch street and 92 Maple Street in Lewiston, Maine. Contractor represents itself to be experienced and competent to perform, and agrees to perform, the services under this Agreement as set forth in the Contract Documents consisting of Asbestos Abatement Work Plan- Apartment Buildings at 80 Birch Street and 92 Maple Street- Lewiston, Maine by Summit Environmental Consultants dated August 20, 2013 and the Quote Form and Quote Submittal Package dated. The contract schedule shall commence with the Notice of Award dated August, 2013. All work shall be completed no later than October 11, 2013. 2. Compensation The work set forth in the Contract Documents will be performed on a lump sum basis in accordance with the Quote Proposal Form submitted by 2:00 p.m. on September 4, 2013. The contract amount of $ ) is based on the scope of work specified in the documents referenced in Paragraph 1 above. 3. Termination a.) The City may terminate this Agreement by written notice to Contractor in the event that Contractor fails to commence its services hereunder, or any portion thereof, within the specified time or otherwise fails to comply with any material term of this Agreement or if Contractor becomes insolvent, petitions for protection under any bankruptcy or creditor's laws or if any involuntary petition for such relief is filed by any creditors or Contractor. In the event of termination under this subsection a) no further payment will be made to Contractor until the services provided for hereunder have been completed by a third party (or parties) selected by the City and paid for. If the total amount paid to such third party (or parties) exceeds the maximum compensation stated in the Compensation provision, Contractor agrees to repay the deficiency to the City. If such amount is less than the maximum compensation, the difference 80 Birch Street and 92 Walnut Street Page AS-1 Agreement For Services